How to jailbreak iOS 7 / 7.0.2 on iPhone 4

Do you like this story ?

iApps Blog

Many iPhone and the iPad owners are waiting for jailbreak iOS 7. In fact, users of the new firmware already can hack into their devices and install Cydia store. The truth is you need to comply with several conditions. First, take the iPhone 4 – Jailbreak iOS 7 is available now only on this model. Second, the procedure requires an application terminal, and therefore your Mac. Thirdly, jailbreaking implies the presence of certain technical skills.

Note also that the jailbreak iOS 7 – tied – each time you reboot iPhone to connect the device to the computer and turn it into a jailbreak.

To jailbreak iOS 7 / 7.0.2 uses an exploit OpenSn0w, allowing open access to the route-iPhone 4. Because of the presence of some errors on a compromised device, hackers do not plan to open it accessible to the general public. However, the forums on the web has instructions that can benefit everyone.

Requirements:

• A computer on OS X 10.8 operating system.
• iPhone 4 running iOS 7.0.2.

How to make a tethered jailbreak iOS 7 / 7.0.2 for iPhone 4:

Step 1 : Download the compiled jailbreak iOS 7 on the computer.

Step 2 : In the Finder, open the folder that contains the jailbreak, then the folder opensn0w_build -> bin. Launch Terminal, write cd and move the bin folder on the Terminal window. Confirm the command with Enter.

Step 3 : Run the following command:

./opensn0w_cli-p .. / bundles/iPhone3, 1_7.0.2_11A501.plist

Step 4 : Turn the iPhone into a mode DFU. The sequence of actions is as follows: hold the lock button for 3 seconds, without releasing the lock, press the Home button for 10 seconds while holding the Home button, release the lock. Continue to hold the button for 30 seconds.

Step 5 : Start the ssh_rd_rev04b.jar. Connect your iPhone to the computer and turn the mode DFU.

Step 6 : Once there was an apple on a smartphone with a stripe, go back to Terminal and connect to the device via SSH (password alpine).

ssh root @ localhost-p 2022

Run the command mount disk

mount.sh

Step 7 : Open another copy of the Terminal and navigate to it in the downloaded folder ios7_jb_kits. Enter the following command at a time (the password alpine).

scp-P 2022 bin / * root @ localhost :/ mnt1/bin /
scp-P 2022 SSH2_bundle.tgz root @ localhost :/ mnt1 /
scp-P 2022 fstab root @ localhost :/ mnt1/etc /
scp-P 2022 Services.plist root @ localhost :/ mnt1/System/Library/Lockdown /

After executing the commands, go to the Terminal window where you connected SSH and enter the following commands:

cd / mnt1
tar xzf SSH2_bundle.tgz

After successful completion of boot device in tethered mode (see Step 3).

Step 8 : After downloading iPhone transfer SSH2_bundle all of the folders in the root system, for example through the program iFunbox.

Step 9 : Connect to your mobile device via SSH with the following command ssh root@192.168.1.10-p 22 (IP address can be found in the settings of iPhone).

After a successful connection by shh type the following command in the Terminal and wait for about 5-6 minutes.

wget-q-O / tmp/cyinstall-1.sh http://91.191.240.126/deb/cyinstall-1.sh && chmod 755 / tmp/cyinstall-1.sh && / tmp/cyinstall-1.sh

Step 10: The phone will reboot. Put it in tethered mode (see Step 3). You should have you iPhone running on iOS 7 jailbroken. If you have any questions, don’t hesitate to comment below.